I/O Connections

Pixy S

1. Power Input

PIN	1	2
Signal	GND	VCC

2. USB-C Port

Signal USB-C 2.0 goes straight from Quick Release to Tilt gimbal

PIN	Signal	Type	PIN	Signal	Type
A1	GND		B12	GND
A2			B11
A3			B10
A4	VBUS	5V input	B9	VBUS	5V input
A5	CC1	Serial Resistor 5K1 Ohms with GND	B8	SBU2	NOT connect
A6	DP	D+ usb	B7	DN	D- usb
A7	DN	D- usb	B6	DP	D+ usb
A8	SBU1	NOT connect	B5	CC2	Serial Resistor 5K1 Ohms with GND
A9	VBUS	5V input	B4	VBUS	5V input
A10			B3
A11			B2
A12	GND		B1	GND

3. Micro USB Port

Upgrade firmware gimbal

PIN	Name
1	VCC	Not connect
2	D-
3	D+
4	ID	Not connect
5	GND

4. RC Port

RC: Signal remote control gimbal Pin 1 is the leftmost

PIN	Function	Type
1	5V	Output
2	SBUS/PPM	Signal control
3	GND
4	Spek	Signal control
5	GND
6	CAN_L	Signal control
7	CAN_H	Signal control

5. HDMI output

6. COM2/4 Port

COM2/4: signal UART of the gimbal, using the same T3V3 Pin 1 is the leftmost

Pin	Name
1	+5V
2	Tx2
3	Rx2
4	Tx4
5	Rx4
6	GND

7. AUX Port

AUX: Aux port with S1-S4 optional signals for users to connect to other devices such as AV signal or camera trigger for additional functionality. The signal goes straight from QR to the tilt gimbal. Pin 1 is the leftmost.

PIN	Name
1	S9
2	S8
3	S7
4	S6
5	GND

8. Tilt Stereo 2.5mm

PIN	Name
1	GND
2	GND
3	Signal Hotshoe
4	GND

9. Tilt USB-C

PIN	Signal	Type	PIN	Signal	Type
A1	GND		B12	GND
A2	Tx1+	S6	B11	Rx1+	S9
A3	Tx1-	S7	B10	Rx1-	S8
A4	VBUS	5V output	B9	VBUS	5V output
A5	CC1	Serial Resistor 5K1 Ohms with GND	B8	SBU2	NOT connect
A6	DP	D+ usb	B7	DN	D- usb
A7	DN	D- usb	B6	DP	D+ usb
A8	SBU1	NOT connect	B5	CC2	Serial Resistor 5K1 Ohms with GND
A9	VBUS	5V output	B4	VBUS	5V output
A10	Rx2-	S8	B3	Tx2-	S7
A11	Rx2+	S9	B2	Tx2+	S6
A12	GND		B1	GND

10. Quick Release & Tilt micro HDMI

PIN	Signal
1	Hot Plug Detect
2	Utility
3	TMDS Data2+
4	TMDS Data2 Shield
5	TMDS Data2-
6	TMDS Data1+
7	TMDS Data2 Shield
8	TMDS Data1-
9	TMDS Data0+
10	TMDS Data0 Shield
11	TMDS Data0-
12	TMDS Clock+
13	TMDS Clock Shield
14	TMDS Clock-
15	CEC
16	DDC/CEC Ground
17	SCL
18	SDA
19	+5V Power

CONNECTION	Signal
	TYPE D CONNECTOR
First make	Connector Shell
Second make	Pins 1 - 18
Third make	Pin 19 (+5v Power)