S-PORT

QUICK RELEASE: S-PORT (MIO QUICK RELEASE)

S-Port also known as Gremsy Mio Quick Release. A standard Quick Release across multiple light products enables the hot swap functionality of payloads or gimbals, thereby enhancing the optimization of drone systems for diverse photogrammatical missions such as mapping, inspection, surveying, etc. and efficiency during these missions.

This product is compatible with

pageVIOpageZIOpagePixy LR SPpageMIO

I/O CONNECTION

1. POWER:

Input range: 14.5V-52V Connector type: JST SM02B-SFKH-TF

2. USB:

Use to interface with computer or upgrade firmware. Connector type: Micro USB type B

3. HDMI:

Use to output video from the camera Connector type: HDMI micro

4. MTX:

Multiplex port that combines AUX , COM1/COM2/COM4 ,CAN, SBUS,PPM into a single connector.

In order to access these interfaces easily, it is necessary to use MTX hub.

Connector type: 3 pin, 2.54mm pitch

CONNECT QUICK RELEASE

STEP 1: The marks on the top part and bottom part must be aligned. The mark on the ring should be aligned with the unlocked icon as shown in the first picture.

STEP 2: Keep everything aligned and attach the bottom part to the top part.

STEP 3: Rotate the ring clockwise until the mark on the ring aligned with the locked icon.

DISCONNECT QUICK RELEASE

STEP 1: Rotate the ring counterclockwise.

STEP 2: When the mark on the ring aligned with the unlock icon, the MIO can be detached from the top part of the Hyper Quick Release.

MTX HUB CONNECTORS & PINOUTS

1.COM1/CAN:

COM1 is a serial protocol (UART) port which is used to interface with a computer via USB.

CAN is to interface with DJI Flight controller.

Connector type: JST SM06B-GHS-TB(LF)(SN).

2.COM2/COM3:

COM2/COM3 is serial protocol (UART) port, this port is internally connected to COM2/COM3 port on the gimbal controller.

  • COM2 is to interface with Pixhawk via Mavlink protocol or other modules that use serial protocol (UART).

  • COM3 is reserved for future use.

Connector type: JST SM06B-GHS-TB(LF)(SN).

3.SBUS/PPM:

SBUS/PPM to

interface with SBUS/PPM receiver. This port is internally connected to SBUS/PPM port on the gimbal controller.

Connector type: 3 pin, 2.54mm pitch.

4.AUX:

there are optional signals S1, S2, S3, S4, S5, S6, S7, S8 (0.25A max) for users to connect to other devices such as AV signal or camera trigger, ....This port is internally connected to AUX port on the tilt axis.

Connector type: JST SM09B-GHS-TB(LF).

TILT CONNECTORS & PINOUTS

1.AUX:

Provide 12V output (1A max) to power camera and accessories and optional signals S1, S2, S3, S4, S5, S6, S7, S8 (0.25A max) for users to connect to other devices such as AV signal or camera trigger, ....This port is internally connected to AUX port on the hyper quick release.

Connector type: JST SM10B-GHS-TB(LF).

2.HDMI:

This connector allows HDMI video output from the camera to the HDMI Micro connector on the Quick Release.

Connector type: HDMI Micro.

MOUNTING HYPER QUICK RELEASE

  • Using 4xM2.5 to mount the top part onto the frame or damping isolator.

  • Pay attention to the arrow on the hyper quick release which indicates the home or forward position of the gimbal.

  • Connect the power cable to the Hyper Quick Release.

  • Connect the MTX cable to the Hyper Quick Release and MTX hub.

Last updated